Variational Derivative for Buckling Loads of Beams and Frames

The finite-difference method is a numerical technique for obtaining approximate solutions to differential equations. The main objective of the present study is to give a new aspect to the finite-difference method by using a variational derivative. By applying this formulation, accurate values of the buckling loads of beams and frames with various end supports are obtained. The performance of this formulation is verified by comparison with numerical examples in the literature __________ Published in Prikladnaya Mekhanika, Vol. 41, No. 7, pp. 139–144, July 2005.     

Stability and Nonlinear Deformation of Cylindrical Grids

The general stability of single-layer cylindrical grids is studied in linear and nonlinear formulations. Dependence of the general buckling load on the geometry and stiffness parameters of a grid is established in an analytical form. Such grids are numerically analyzed for stability. It is established that the general buckling load is much less than the local buckling load. Typical general buckling modes are found. It is shown that such grids are weakly sensitive to imperfections     

A parallel cell‐based DSMC method on unstructured adaptive meshes

A parallel DSMC method based on a cell‐based data structure is developed for the efficient simulation of rarefied gas flows on PC‐clusters. Parallel computation is made by decomposing the computational domain into several subdomains. Dynamic load balancing between processors is achieved based on the number of simulation particles and the number of cells allocated in each subdomain. Adjustment of cell size is also made through mesh adaptation for the improvement of solution accuracy and the efficient usage of meshes. Applications were made for a two‐dimensional supersonic leading‐edge flow, the axi‐symmetric Rothe's nozzle, and the open hollow cylinder flare flow for validation. It was found that the present method is an efficient tool for the simulation of rarefied gas flows on PC‐based parallel machines. Copyright © 2004 John Wiley & Sons, Ltd.     

强流四脉冲电子束源实验研究

 为了进行强流多电子束源研究，对现有2MeV LIA 注入器进行了四脉冲改造，二极管脉冲电压约500kV。实验研究了天鹅绒阴极在四脉冲条件下的发射能力、传导电流负载效应以及阴极等离子体运动对阴极电子发射和束能量的影响。利用空间电荷限制流模型推算出阴极等离子体膨胀速率在1 ~4cm/μs之间。     

多段构件组成的压杆平面内稳定

分析由若干段等截面或者变截面构件组成的压杆平面内稳定问题．从由三段等截面构件组成的压杆平面内稳定问题出发，对两端为变截面、中间为等截面构件组成的压杆的平面内稳定问题进行了分析，得出和两端为等截面构件情况类似的屈曲荷载计算公式．并对两端固接的情况进行了研究分析．     

Randomization helps to perform independent tasks reliably

This paper is about algorithms that schedule tasks to be performed in a distributed failure‐prone environment, when processors communicate by message‐passing, and when tasks are independent and of unit length. The processors work under synchrony and may fail by crashing. Failure patterns are imposed by adversaries. Linearly‐bounded adversaries may fail up to a constant fraction of the processors. Weakly‐adaptive adversaries have to select, prior to the start of an execution, a subset of processors to be failure‐prone, and then may fail only the selected processors, at arbitrary steps, in the course of the execution. Strongly adaptive adversaries have a total number of failures as the only restriction on failure patterns. The measures of complexity are work, measured as the available processor steps, and communication, measured as the number of point‐to‐point messages. A randomized algorithm is developed, that attains both ??(n log*n) expected work and ??(n log*n) expected communication, against weakly‐adaptive linearly‐bounded adversaries, in the case when the numbers of tasks and processors are both equal to n. This is in contrast with performance of algorithms against strongly‐adaptive linearly‐bounded adversaries, which has to be Ω(n log n/log log n) in terms of work. © 2003 Wiley Periodicals, Inc. Random Struct. Alg., 2004     

Load-Carrying Capacity of Circular Plates Made of a Fiber-Reinforced Composite

The load-carrying capacity of circular plates made of a fiber-reinforced composite and loaded with axisymmetric transverse forces under axisymmetric boundary conditions is investigated. The plates can be freely supported or clamped along their contour. To the known yield condition used, in the plane of main bending moments, there correspond irregular hexagons, which depend on the mechanical properties of composite constituents and some characteristic geometrical parameters. It is shown that, depending on the ratio of ultimate radial and circumferential bending moments, in the plastic state, the circular plates (the central part of the clamped plates) take the form of a cone or a frustum of cone. For each of the cases, the limit load is found, which is a function of the above-mentioned mechanical parameters. The statically allowable fields of bending moments and the corresponding allowable fields of deflection rates are determined. The solutions found are exact. Special cases for the freely supported plates are analyzed, and the results obtained are presented in the form of graphs.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 177–192, March–April, 2005.     

Effect of a Shock Pulse on a Floating Ice Sheet

The vibrations of a viscoelastic plate lying on an elastic liquid base subjected to pulse loading have been studied theoretically and experimentally. The effect of the variable depth of the reservoir, plate thickness, and strain relaxation time on the value of the plate vibration amplitude and the length and curvature of the flexural gravity wave profile are analyzed. Good agreement of theoretical and experimental results is obtained.     

集中荷载下叠合梁抗剪强度

本文对低叠合面钢筋破简支在合梁二阶段受力的斜截面抗剪性能进行了试验研究，并运用非线性有限元分析和试验实测数据，得出了一个适合于集中荷载下高低叠合面叠合梁的抗剪强度计算公式．     

复合多层介质在可变温度和集中荷载作用下的位移和应力

研究了多层介质中的热弹性位移和应力.多层介质具有不同厚度,各层又具有不同的弹性性质,最上层表面上作用热荷载和集中荷载.假设各层分别是均匀、各向同性弹性材料,各层相关的位移分量是轴对称的,对称轴为各层表面的垂线.因此,各层应力函数满足无体力的单一方程.利用积分变换法求解了该方程,对由任意多个层数构造的多层介质,给出了其相应层数基础热弹性位移和应力的解析表达式.并对3层介质和4层介质时的数值结果进行了比较.